What does a diesel aftertreatment system do?
A diesel aftertreatment system cleans the exhaust in two stages: a diesel particulate filter (DPF) traps soot, cutting particulate matter by 85 to 90% or more (EPA, 2010), and a selective catalytic reduction (SCR) catalyst turns NOx into nitrogen with ammonia made from diesel exhaust fluid (DEF), a 32.5% urea solution that freezes at about 12°F (GM, in a 2011 talk hosted by EPA).
The filter cleans itself by burning the soot to ash, called regeneration. It happens on its own when the exhaust is hot enough (passive) or with added fuel or heat (active), and EPA's bulletin notes an active regeneration may need the driver to act. Ash doesn't burn, so the filter needs cleaning in time. Sensors watch every stage, and each sets its own SPN.
What do the 13 aftertreatment SPNs mean?
The 13 aftertreatment SPNs are five DPF codes, four DEF codes, two NOx sensors, the SCR efficiency code and the SCR inducement (derate) code; SPN 3251 and SPN 4364 are searched most, at 720 a month each (read November 16, 2026).
| SPN | Part or signal | Common FMIs, as makers word them | Searches |
|---|---|---|---|
| 3251 | DPF differential pressure | 16 or 0: pressure across the filter high (Daimler, Cummins) | 720 |
| 4364 | SCR catalyst conversion efficiency | 18: NOx conversion efficiency low (both) | 720 |
| 3216 | NOx sensor, SCR intake | 4: circuit low; 20, 21: drifted (both) | 590 |
| 3226 | NOx sensor, SCR outlet | 4: circuit low; 13: no signal (Daimler) | 590 |
| 5246 | SCR operator inducement | 15: derate on; 0: final action, speed limit (Daimler) | 590 |
| 1761 | DEF tank level | 1: empty, speed limited (Daimler) | 210 |
| 3719 | DPF soot load | 16: soot high; 0: very high (Daimler) | 210 |
| 3936 | DPF system | 7: incomplete regeneration (Daimler) | 210 |
| 3364 | DEF quality | 17, 18: improper DEF quality warning (Daimler) | 140 |
| 3610 | DPF outlet pressure | 0: system back pressure too high (Daimler) | 140 |
| 4374 | DEF pump | 0: DEF system under-pressurized (Daimler) | 140 |
| 4334 | DEF pressure | 7: DEF pressure low (Daimler) | 110 |
| 3720 | DPF ash load | 15: ash clean request; 16: ash derate request (Daimler) | 110 |
What are DPF codes?
DPF codes are SPN 3251, 3719, 3936, 3610 and 3720: they report the pressure across the filter, its soot and ash load, the pressure behind it and whether a regeneration finished, and together drew 1,390 US searches a month on November 16, 2026.
SPN 3251 FMI 16 or 0 means the filter is restricting flow more than it should, usually from soot or ash, while FMI 3 or 4 points at the pressure sensor's circuit instead (Cummins' table). SPN 3719 is the computer's soot estimate, and Daimler's table lists "Incomplete Regeneration" as SPN 3936 FMI 7. Ash builds up whatever you do: Daimler's SPN 3720 FMI 15 is an ash clean request and FMI 16 an ash derate request, so that filter needs cleaning, not a regen.
What are SCR fault codes and NOx sensor codes?
SCR fault codes and NOx sensor codes are SPN 4364, 3216 and 3226: the engine computer compares the NOx sensor before the catalyst (3216) with the one after it (3226), and when too little NOx is removed it sets SPN 4364, low conversion efficiency. These three drew 1,900 US searches a month on November 16, 2026.
A low-efficiency code doesn't name the cause. Bad DEF, a dosing fault, a worn catalyst or a drifting sensor can each make the numbers disagree, which is why both makers' tables give the NOx sensors their own drift codes (FMI 20 and 21). Daimler's table lists 16 FMIs for the intake sensor alone.
What are DEF codes?
DEF codes are SPN 1761 (tank level), 3364 (fluid quality), 4374 (pump) and 4334 (pressure): they report whether there is enough fluid, whether it is the right fluid, and whether the pump is delivering it, and drew 600 US searches a month on November 16, 2026.
Low fluid is the simplest case: Daimler's table counts SPN 1761 down from "Low" (FMI 31) to "Empty (Speed Limited)" (FMI 1). A quality code (SPN 3364) means the sensor doesn't read the expected urea mix, from water, the wrong fluid or a sensor fault. DEF freezes at about 12°F, which is why the tank and lines are heated, and it thaws with no harm (GM).
Why do aftertreatment codes derate the engine?
Aftertreatment codes derate the engine because the SCR system is built to push the driver into fixing an emissions fault, which is what "operator inducement" in SPN 5246's name means: SPN 5246 the SCR operator inducement, steps from "Derate On" (FMI 15) to "Final Action Pending" (FMI 16) to "Final Action (Speed Limit)" (FMI 0) in Daimler's table.
On Cummins engines the same code shows a Cummins number too: fault code 3712 is SPN 5246 FMI 0 on the ISX15 (Diesel Laptops). SPN 5246 is a result, not a cause: look for the DEF, NOx or SCR code that started it.
What should you check first on an aftertreatment code?
Check the cheap things first: DEF level and fluid, connectors and wiring, and exhaust leaks, because Noregon, the maker of JPRO, warns that wiring, connectors, corrosion and voltage problems set the same codes as a failed sensor. Clearing the code doesn't fix it.
- Write down every active code, with SPN, FMI and count.
- Fix the oldest or root code first: a NOx sensor or DEF code can come before SPN 4364 and 5246.
- For FMI 3 to 6, look at the sensor's connector and harness for damage and corrosion before buying the part.
- For DPF pressure codes, check the sensor hoses for cracks or blockage: EPA's DPF bulletin says a backpressure monitor should always be used and checked to confirm it works.
- Use the maker's software or a dealer for forced regens and tests.
Where can you get repair steps for an aftertreatment code?
Repair steps for an aftertreatment code come from the engine maker's software, a free code lookup, a repair app or a shop: Diesel Repair Desktop is $0, Cummins INSITE Lite is $1,325 for 12 months, and Mechy's first 3 guides are free (prices read November 16, 2026).
| Option | What you get | Price |
|---|---|---|
| Diesel Repair Desktop | Pick the engine, pick the code, read the solution; works offline | $0 |
| Mechy | Type the code and machine; numbered steps with tools and parts. Doesn't read the truck or diagnose; AI-written, can be wrong | Free first 3 guides; $79/yr or $9.99/mo |
| Cummins INSITE v8 Lite | Cummins' software: fault information, wiring diagrams, engine tests | $1,325 / 12 months |
| Dealer or diesel shop | A technician with the maker's tools | Shop rate |
To read the code in the first place, the ways to read a J1939 code start at $240 for a phone adapter, and the FMI list explains the second number.
How this page was checked
Every code name was re-read in Kato Works' copies of the Cummins and Daimler tables; DPF facts in EPA bulletin EPA-420-F-10-029; DEF facts in GM's 2011 talk on EPA's site; the derate example in Diesel Laptops' ISX15 list; checking advice in Noregon's guide; prices and searches as on the data page. All read November 16, 2026. Published by Winding AI, Inc., the company that makes Mechy. Back to J1939 codes explained.